The EXP-EMG-EXT-LE6-3L from
Larson Electronics is an Explosion Proof Bug Eye Emergency LED Exit Sign Light
Fixture that is Class I, Divisions 1 & 2, Groups B, C, D, Class I, Zones
1 & 2, Groups IIB+H2, IIA, Class II, Divisions 1 & 2, Groups E, F, G and
Class III Divisions 1 & 2 rated for hazardous areas. The EXP-EMG-EXT-LE6-3L
produces 99 total fixture lumens while drawing only 3.3 total watts and will
operate for at least 90 minutes in the event of a power failure or outage. This
unit is self-testing, has a 24 hour battery recharge time following emergency
operation and operates on 120/277V AC @ 60Hz. The EXP-EMG-EXT-LE6-3L is an ideal
solution for providing emergency lighting and exit marking. This single sided
exit sign is an ideal emergency exit marking solution for hazardous locations
where failsafe reliability is a must.
EXP-EMG-EXT-LE6-3L explosion proof emergency bug eye LED exit sign light fixture
is ideal for installation in hazardous areas that require emergency illumination
in the event of a power failure or power outage. This fixture features three
explosion proof enclosures that are configured in a bug eye layout and a bottom
mounted single sided exit sign. The two upper enclosures house the LEDs while
the center enclosure contains an indicator light and the exit sign hangs down
below. The unions between the upper enclosures, the indicator light enclosure
and the exit sign allow for both horizontal and vertical adjustment.
The EXP-EMG-EXT-LE6-3L features three lamps that each contain eight LEDs that
draw a total of 1.1 watts per lamp. Each lamp produces 33 lumens of
high-intensity white LED light for a fixture total of 99 lumens produced while
drawing a total of 3.3 watts. This explosion proof emergency LED exit sign light
fixture features brown-out, short circuit and voltage surge protection and has a
low voltage disconnect which prevents damage to the battery caused by a deep
discharge. This self-testing LED fixture will run for at least 90 minutes after
a power failure thanks to the maintenance-free 3.6 volt NiCad battery. After
emergency use, the battery takes 24 hours to completely recharge.
Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no
filaments or fragile housings to break during operation and/or transportation.
Instead of heating a small filament or using a combination of gases to produce
light, light emitting diodes (LEDs) use semi-conductive materials that
illuminate when electric current is applied, providing instant illumination with
no warm up or cool down time before re-striking. Because there is no warm up
period, this light can be cycled on and off with no reduction in lamp
lights run at significantly cooler temperatures than traditional metal halide
and high pressure sodium lights and contain no harmful gases, vapors, or
mercury, making them both safer and more energy efficient. No extra energy is
wasted in cooling enclosed work areas due to external heat emissions from bulb
type lights, and the operator risks associated with traditional lighting
methods, such as accidental burns and exposure to hazardous substances contained
in the glass bulbs, are eliminated. In addition, LEDs are also safer for the
environment as they are 100% recyclable, which eliminates the need for costly
special disposal services required with traditional gas burning and arc type
Operation: The EXP-EMG-EXT-LE6-3L features a backup battery that will
run the fixture for at least 90 minutes following a power outage or any other
loss of power. The included emergency backup battery is a 3.6 volt NiCad
rechargeable unit. These batteries are maintenance-free and have a life
expectancy of 15 years while being able to operate in a wide variety of
conditions including in temperatures ranging from 0°C to +40°C. This unit also
features a low voltage disconnect. This means that if the fixture detects that
the battery`s terminal voltage has fallen below a certain level, the low voltage
circuit will disconnect the emergency lighting load until normal power is
restored. This prevents the battery from experiencing a deep discharge and
Ratings: The EXP-EMG-EXT-LE6-3L from Larson Electronics is an explosion
proof emergency LED fixture. This particular unit is Class I, Divisions 1 &
2, Groups B, C, D, Class I, Zones 1 & 2, Groups IIB+H2, IIA, Class II,
Divisions 1 & 2, Groups E, F, G and Class III Divisions 1 & 2 rated for
EXP-EMG-EXT-LE6-3L explosion proof emergency self-testing LED fixture is
NOT a factory sealed fixture. Operators will bring their own
wiring to a junction box and complete their connects. The operator will also
provide their own seal off for this fixture. The EXP-EMG-EXT-LE6-3L operates on
120/277V AC @ 60Hz.
EXP-EMG-EXT-LE6-3L is designed to be surface mounted to flat surfaces such as
walls. The unions connecting the upper lamps to the lower indicator light
enclosure and the exit sign allow for both horizontal and vertical adjustment.
This gives operators the ability to adjust the light to their specific mounting
location for ideal light coverage during a power failure or power
Applications: The EXP-EMG-EXT-LE6-3L is ideal for use as emergency exit
lighting in areas where an explosion proof fixture is required.
Larson Electronics, we do more than meet your lighting needs. We also provide
replacement, retrofit, and upgrade parts as well as industrial grade power
accessories. Our craftsmen can custom build any lighting system and/or
accessories to fit the unique demands of your operation. A commitment to
honesty, quality, and dependability has made Larson Electronics a leader in the
lighting and electronics business since 1973. Contact us today at 800-369-6671
or message email@example.com
for more information about our custom options tailored to meet your specific
1. Low power consumption.
3. Fixture constructed of extruded corrosion resistant
copper free aluminum alloy.
4. Superior color rendering compared to HPS, LPS,
5. Retains 70% lumen output after 100,000 operating hours.
coated aluminum fixture body.
7. Surface mount included
8. Low profile -
9. 99 Lumen output from 3.3 watts
10. 90 minute emergency
runtime. 24 hour battery recharge time.
1. 100,000+ hour lifespan.
2. Can SAVE 50% or
more on energy.
3. Qualifies retrofit projects for financial incentives,
including utility rebates, tax credits and energy loan programs.
energy use and prolongs life-spans of peripheral cooling units (A/C,
5. 100% recyclable.
6. No toxins-lead, mercury.
7. No UV
light, infrared radiation or CO2 emissions.
8. Qualifies buildings for LED
and other sustainable business certifications.
9. Bright, even light
maintains consistent color over time.
10. Instant on/off - No flickering,
delays or buzzing.
11. Very good color rendering.
13. Significantly cooler operation.
14. Less frequent outages,
higher output improves workplace safety.
Specifications / Additional
Explosion Proof Emergency LED Exit Sign
Scroll Down to
||Class I, Divisions 1 &smp; 2, Groups B, C,
16"L x 36"H x 6"D
||Class I, Zones 1 & 2, Groups IIB+H2|
||Class II, Divisions 1 & 2, Groups E, F, G|
120/277V AC, 60Hz
||Class III Divisions 1 & 2|
||90 Minute Emergency Runtime|
||24 Hour Battery Recharge Time|
|Luminous Efficacy: 30 Lm/W
|LED Light Color: White
||Horizontal and Vertical Adjustable|
|LED Life Expectancy: 100,000 Hours
|Emergency Runtime: 90 Minutes
Maintenance-Free 3.6 Volt NiCad Rechargeable Battery
Time: 24 Hours
Expectancy: 15 Years
Operator Provided Wiring & Seal Off
|Adjustability: Lamp Heads
Horizontally & Vertically Adjustable
|Housing Material: Die Cast Aluminum
||Contact us for special requirements |
|Housing Color: Powder Coated - Grey
|Lens Material: Polycarbonate
Yes - 1 Year*